A list of Chinese analog panel meter style numbers and measurements

 

A list of Chinese analog panel meter style numbers and measurements

(because I could not find it anywhere, and decided to compile this list)

So45 45mm circle

62c5, 62t51 80mm circle

SD65 82mm circle

SD50 50x50mm

85c1 56x64mm

SD60, YT60 60x60mm

SD670, YT670 60x70mm

69C9, 69I9 64x80mm

44C2, 44I1, 44L1 80x100mm

59I1, 59C2, 99T1 100x120mm

CP48, 99C1, 99T2, 99T1 48x48mm

YT72 72x72mm

6C2 80x80mm, 76x76mm

6C2B 80x80mm, 76x76mm B

CP96 96x96mm

42C3 120x120mm

85C17, 85L17 40x70mm

96C17, 96L17 46x86mm

61x108mm

59c23, 59I23 69x129mm

F96-ACB, F72-ACB SHIP meter



Comments

Post a Comment

Popular posts from this blog

Characterizing some LEDs

Image
 Not every LED selling source can supply high quality datasheets. When the prices are too good to ignore, it's time to do your own characterization. What is needed ... • a voltage source - My voltage supply is a Ryobi 18v battery, with an adapter found on eBay for powering Hot Wheels go karts. The adapter has both an on/off switch and an inline fuse. The default fuse is 30A, but I've changed mine to 3A. • a mini board that holds a regulator - These are little PCBs that will hold one adjustable regulator (AMS1117-ADJ or LM317LZ, your choice, they both have a 1.25v Vadj terminal. You will be using this device as a two-terminal constant current regulator circuit. This means that There is a Vin, a Vadj, and a Vout. You have to supply a resistor to program what current value the regulator is targeting. The regulator will then home in on the desired current, while dropping any excess voltage required to do this. • a mini board with positions for 8 SMD resistors - I'm partial to ...
Read more

The basic theory behind light emitting diodes

Image
 This is a Voltage/Current curve of a typical light emitting diode. The exact values of each spot on the curve are less important, but the curve and what happens in each segment, is more important. Segment A - Voltage is increasing, but has not yet reached the point where the diode junction is emitting enough light to be visible. If you have a datasheet for the device, this will probably be the first 75%-80% of the rated forward voltage (Vfwd). Segment B - As the forward voltage enters the knee part of the curve, light may be perceived. Depending on the exact voltage and/or the current, the light may be faint. Once you have entered the curve area, forward current will begin to change as the voltage increases. Depending on the exact device ratings, the device may begin to dissipate some heat. Heat will be low to negligible, increasing as you approach the device rated forward current. Light should be obvious, and increasing as you move deeper into the knee area. Segment C - The light...
Read more

Making the LED knee region larger and more easily usable

 In an earlier blog post, I talked about the knee region. This is the area of an LED's voltage-current curve, where the current begins to increase sharply. For most 3v LEDs, the knee region is a fairly small voltage range. Controlling the knee region requires a very careful adjustment of voltage.  There is a way to expand the knee region: connect multiple LEDs in series !  All the LEDs voltage aspects are cumulative, when connected in series. So the overall vFwd increases by the number in series, but so does the voltage range of the knee region. The basic assumption here is that all the LEDs you are connecting in series have the same data sheet part description, and also they were binned together voltage wise. A single LED might have a knee region that is only 0.1v-0.2v wide. By placing five in series, the voltage rage of the knee region now becomes a range of 0.5v-1.0v wide. An additional advantage of five (or six) in series, is that you can power it with a 15-20 volt su...
Read more